AS/NZS 3112电流负载型插头插座寿命试验机

电流负载型插头插座寿命试验机是根据标准AS/NZS 3112第3.14.4节、BS1363-1第12.9.5节设计生产的.

标准要求：

 12.9.5.1 Conformity shall be checked by the following tests.

The test is carried out with plugs with nickel plated brass pins and/or non-solid pins and three different types of new socket-outlets in accordance with BS 1363-2:2016. Two types of the socket-outlet shall have the shutters operated by the earth pin, one of which is preferably operated by all three pins and one of which is preferably operated by line and neutral pins only.

The combination of rewirable plugs having nickel plated brass pins and/or non-solid pins and each type of socket-outlet as described shall make and break a current of 13 A ±0.4 A, non-rewirable plugs shall be tested with the rated current appropriate to the flexible cable given in Table 2, at 250 V ±10 V a.c. 15 000 times (30 000 movements) in a substantially non-inductive circuit.

Each plug is inserted into and withdrawn from the socket-outlet at a rate of six insertions and six withdrawals per minute, the speed of travel of the plug being approximately 150 mm/s. The periods during which the plug is inserted and withdrawn shall be approximately equal. The plug pins are renewed or a new plug is used after each 5 000 insertions and withdrawals. For the purpose of this test no lubrication shall be applied to the pins of the plug or the socket-outlet contacts.

After the test the shutters of the socket-outlets shall be operating satisfactorily, the socket contacts safely shielded and the socket-outlets shall be in accordance with 9.1, 16, 15, 13.4.1a), 10.2, 13.6, 13.7 and 13.8 of BS 1363-2:2016 and the permitted values of voltage drop specified in 13.4.1a) of BS 1363-2:2016 for the plug pin to socket contact measurements increased by 50%. The pins of the plug shall remain intact with no openings in the surface, joints or seams which will accept the probe specified in 12.9.3. There shall be no visible evidence of peeling or flaking of plating.

12.9.5.1具有类似的要求。

AS/NZS 3112标准要求：

3.14.4 Current breaking test

With the exception of interlocked socket-outlets and socket-outlets switched by insertion of plug pins complying with Clause 3.11, socket-outlets shall be subjected to the test set out in this Clause.

Socket-outlets shall be tested using a test plug with brass pins having dimensions complying with this Standard.

The plug shall be inserted into, and withdrawn from, the socket-outlet 50 times (100 strokes) at a rate of 150 mm/s and 30 strokes per minute.

NOTE: A stroke is an insertion or a withdrawal of the plug.

The test voltage shall be 1.06 times the rated voltage and the test current shall be 1.25 times the rated current.

The test current shall be a.c. with a power factor of approximately 0.75 lagging, or d.c., as appropriate. Where a socket-outlet is intended for both a.c. and d.c. operation, a separate sample shall be tested on each source of supply.

No current shall be passed through the earthing circuit, if any such circuit exists.

The socket-outlet and plug shall be mounted so that the withdrawal movement is in an approximately horizontal direction, and the earthing pin, if any, is at the lowest point.

An appropriate type of plug, complying with this Standard and having a rating corresponding to that of the socket-outlet, shall be used for this test.

During the test, no sustained arcing shall occur.

产品规格参数：

1、7寸彩色触摸屏

2、三菱平台FX系列PLC控制

3、电流可调，0～25A/250V交流，电流变送器经AD模拟量转换显示电流于触摸屏

4、电压不可调，外接调压器调节，可定制带电压调节型机器

5、风冷型阻性负载

6、雷塞步进电机驱动

7、插拔速率：5～200mm/s可调

8、计数次数：0～32767次

9、通电时长可调

10、断电时长可调

11、铝型材、A3烤漆钢板复合结构

12、简易版无电流负载版请参考：AS/NZS 插头插座寿命试验机